There are currently no product reviews.
Hello from Germany - thank you very much for the manual for my Sharp "Searcher" - the handling of your internet area is outstanding..Mike
I am very happy with the owner's manual. I bought a used Casio and was so relieved that I was able to get a hold of a owner's manual. It was very easy to download the manual and I had no problems with printing it. Thank you! Nancy Whalen
The purchased manual is an high-quality scan of the original JVC paper-based OwnerΒ΄s Manual. I am very satisfied!
Very satisfied with received document, all is right, Thank You very much, it was a Pleasure to work with You.
great site, the most easy and fastest way to find the manual you need, no 5 star because the manual was only available in german, but I speak german as well so no problem for me.
SECTION 4 MECHANICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistene swab: playback head pinch roller rubber belt capstan idler 2. Demagnetize the playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the power supply voltage unless otherwise noted. â¢ Torque Measurement
Mode Forward Forward Back Tension Reverse Reverse Back Tension FF, REW Torque Meter CQ-102C CQ-102C CQ-102RC CQ-102RC CQ-201B Meter Reading 30 â 65 gâ¢cm (0.42 â 0.90 ozÂ·inch) 0.5 â 4.5 gâ¢cm (0.01 â 0.06 ozÂ·inch) 30 â 65 gâ¢cm (0.42 â 0.90 ozÂ·inch) 0.5 â 4.5 gâ¢cm (0.01 â 0.06 ozÂ·inch) 60 â 200 gâ¢cm (0.83 â 2.78 ozÂ·inch)
SECTION 5 ELECTRICAL ADJUSTMENTS
TEST MODE This set have the test mode function. In the test mode, FM Auto Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure. <Set the Test Mode> 1. Set the âpower selectâ switch (S501) is âAâ position. 2. Turn ON the regulated power supply. (All LEDs on the set lights up, and the clock is displayed) Note: Press the [OFF] button, if the clock is not displayed. 3. Push the preset  button. 4. Push the preset  button. 5. Press the preset  button for more than two seconds. 6. Then the display indicates all lights, the test mode is set. <Release the Test mode> 1. Push the [OFF] button. 2. Return the âpower selectâ switch (S501) to initially set position.
See the adjustment location from on page 16 for the adjustment.
TAPE DECK SECTION
â¢ Tape Tension Measurement
Mode Forward Reverse Tension Meter CQ-403A CQ-403R Meter Reading more than 90 g (more than 3.18 oz) more than 90 g (more than 3.18 oz)
0 dB=0.775 V
Tape Speed Adjustment Setting:
speed checker or frequency counter 10 k â¦
test tape WS-48A (3 kHz, 0 dB)
set LINE OUT
Procedure: 1. Put the set into the PB mode. 2. Adjust adjustment resistor for inside capstan motor so that the reading on the speed checker or frequency counter becomes in specification. Specification: Constant speed
Speed checker â1.5 to +2.5% Frequency counter 2,955 to 3,075 Hz
Adjustment Location: See page 16.
â 13 â
Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…