|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
;
When I purchased this manual I had my doubts regarding the quality as the price was so reasonable as compared to other outlets.
The manual itself is of high standard the print is very clear as are the diagrams. Obviously with the diagrams one has to zoom in otherwise it is to small to be able to read.
Overall I am very pleased with the company who delivered as they said and with the manual they supplied.
I occasionally require a manual and now having registered with this company I shall order from them in the future.
;
I was at first dubious about payiong for downloaded manuals but having done so, I was extremely impressed with quality of the two manual I ordered, well worth the small price I paid.
I would highly recommend these to my friends.
;
reasonable price for the schematic - the service is perfect, all as expected and pointed by instructions - good scan of the original plans - thank you!
(7) Check first that indication �L� of �AC1L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). n If the �L� indication does not disappear from the LCD (on A area: refer to the previous procedure (5) (when the RF input level is lower than the reference level) or �H� is displayed (when the RF input level is higher than the reference level), perform the following adjustment. 1 Check the RF output level and frequency of the signal generator (perform re-setting if necessary), and repeat from procedure (1). 2 If the above conditions (the �L� indication does not disappear, or �H� is displayed) remain even after re-adjustment, it is necessary to check the WRU-806A Tuner Unit. (8) Indication on the LCD (Tuner [1]) appears as follows: LCD:
(13)Check first that indication �L� of �AC3L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (14)Connect the signal generator to the ANTENNA B IN connector with DC cut fixture. (15)Indication on LCD (Tuner [1]) appears as follows: LCD:
B C1 L
(B C1 L)
A C2 L
(A C2 L)
(16)Set the FREQUENCY(carrier frequency) of the signal generator as follows; FREQUENCY(carrier frequency): U64 model; 772.000 MHz U66 model; 784.000 MHz U68 model; 796.000 MHz (17)Check first that indication �L� of �BC1L� on the LCD has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (18)Indication on the LCD (Tuner [1]) appears as follows: LCD:
(9) Set the FREQUENCY (carrier frequency) of the signal generator as follow. FREQUENCY(carrier frequency): U64 model; 776.000 MHz U66 model; 788.000 MHz U68 model; 800.000 MHz (10)Check first that indication �L� of �AC2L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (11)Indication on the LCD (Tuner [1]) appears as follows: LCD:
B C2 L
(B C2 L)
A C3 L
(A C3 L)
(19)Set the FREQUENCY(carrier frequency) of the signal generator as follows; FREQUENCY(carrier frequency): U64 model; 776.000 MHz U66 model; 788.000 MHz U68 model; 800.000 MHz (20)Check first that indication �L� of �BC2L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (21)Indication on the LCD (Tuner [1]) appears as follows: LCD:
(12)Set the FREQUENCY (carrier frequency) of the signal generator as follow. FREQUENCY(carrier frequency): U64 model; 780.000 MHz U66 model; 792.000 MHz U68 model; 804.000 MHz
B C3 L
(B C3 L)
3-4
MB-806A (U) WRU-806A (U)
|
|
|
> |
|