Shopping cart is empty
 
English Polski Spanish 
Search For a Manual
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Who's Online
There currently are 420 guests online.
Categories
Information
Featured Product
Home >> SONY >> SPPA2780 Owner's Manual
 
 0 item(s) in your cart 

SONY SPPA2780
Owner's Manual


Tweet about this product and get $1.00 of store credit for instant use!
  • Download
  • PDF Format
  • Complete manual
  • Language: English
Price: $4.99

Description of SONY SPPA2780 Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file after You purchase it.

Owner's Manual ( sometimes referred to as User's Guide or User's Manual ) contains information on how to use Your device. After placing order we'll send You download instructions on Your email address.

The manual is available in languages: English

Not yet ready
You must purchase it first

Customer Reviews
There are currently no product reviews.
Other Reviews
 RX-505VLTN JVC Owner's Manual by John Heizer;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
 PM2521 PHILIPS Owner's Manual by David Jesson;
Copy of genuine owners/operators manual, very useful
 RDB365D CLARION Owner's Manual by Tina Whisnant;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
 CXNA10 AIWA Owner's Manual by Roberta Barr;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
 S310 JBL Owner's Manual by Jos Vallen;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!

Text excerpt from page 22 (click to view)
SPP-A2780

HANDSET
• Make the set in the test mode. (See page 15) 1. Power Failure Test Procedure: 1. In the test mode idling status, press the [1] key to display “TEST A”. 2. Check that the key back light on the handset lights up when connect between TP105 and TP104 (GND) on the HAND MAIN board. 2. Low Battery Test Setting:
Handset TP101 TP102 (GND) regulated dc power supply + +3.8 V –

4. Current Measurement Setting:
Handset regulated dc power supply + +3.8 V TP102 (GND) –

A
TP101

Procedure: 1. Connect equipments as the figure above. 2. In the test mode idling status, press the [1] key to display “TEST A”, and press the [5] key. 3. Check that the value of ammeter is 100 to 400 µA.
Note: The set cannot start up if resistance of ammeter is too much.

5.

Between Microphone and Speaker (CODEC Loop

Back) Signal Level Measurement Setting:
audio analyzer 1.2 kHz, –35 dBm LPF: 30 kHz ON Output GND Input

Procedure: 1. Connect equipments as the figure above. 2. In the “TEST A” status, check that the LCD back light on the handset lights up when change the voltage of regulated dc power supply to 3.2 V. 3. Charge Detection and Current Control Test Setting:
digital voltmeter 1 + – regulated dc power supply + +5 V (power off) – 10 Ω charge terminal + charge terminal – + – Handset TP32 TP102 (GND)

10 µF +

Handset TP6 TP5 (MIC GND) TP3

150 Ω GND Base unit RF271 RXAD TXAD short (remove the R284, 285, R287 and R288) RF61 TP4 (GND)

Procedure: 1. Connect equipments as the figure above. 2. Remove the R284, R285, R287 and R288 on the BASE MAIN board. Then connect between RF271 pin qd (RXAD) and RF271 pin qs (TXAD) on the BASE MAIN board by lead wire. Set the [VOL] switch on the handset to [H] position. In the test mode idling status with the handset, press the [4] key of the handset to display “TEST D”. In the test mode idling status with the base unit, press the [4] key of the base unit to display “TEST D”. Set the output level of audio analyzer to –35 dBm (1.2 kHz, LPF=30 kHz ON). Check that the value of audio analyzer is –12 to –18 dBm.

digital voltmeter 2

Procedure: 1. Connect equipments as the figure above. 2. In the “TEST A” status, turn the power on of the regulated dc power supply (+5 V) to start charging. 3. Check that the level of digital voltmeter 1 (voltage of TP32) changes from “L” to “H”. 4. Check that the value of digital voltmeter 2 (voltage of 10 Ω resistor) is 110 to 150 mV. 5. Press the [*] key to start quick charge. 6. Check that the value of digital voltmeter 2 (voltage of 10 Ω resistor) is 1.2 to 1.4 V. 7. Disconnect the regulated dc power supply.

3. 4. 5. 6. 7.

22

You might also want to buy

$4.99

SPPA2780 SONY
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
>
Parse Time: 0.165 - Number of Queries: 113 - Query Time: 0.043