There are currently no product reviews.
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
Service Manual that I received was very helpful to me. Thank you.
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
SECTION 4 TEST MODE
Outline â¢ In this set, overall adjustment mode is made available by entering test mode to perform automatic adjustment of CD and MO. In the overall adjustment mode, the disc is determined whether it is CD or MO and adjustments are performed in sequence. If a fault is found, the location of the fault is displayed. Also, in servo mode, each adjustment can be automatically made. â¢ Operation in the test mode is performed with the remote commander. A key having no particular description in the text, indicates a remote commander key. Setting the Test Mode To enter the test mode, two methods are available : 1. Entering method with key input. Turn on the HOLD switch on the set. While pressing the p key on the set, press the following remote commander keys in the following order : â/+ n â/+ n = n = n â/+ n = n â/+ n = n P n P 2. Entering method by shorting the test point Solder bridge the test point TAP805 (TEST) on the MAIN board (connect IC801 pin #Â£ to GND), and turn on the power. â MAIN BOARD (Conductor side) â Configuration of Test Mode The test mode has the configuration given below.
VOL + key
Overall â/ + key adjustment mode (044 Auto?)
VOL â key
Adjustment â/ + key mode (044 Manu?)
Servo mode 000 VOL +/â keys Audio mode 100 VOL +/â keys Power mode 300
Display when test mode
Displays of the LCD on the remote commander are shown in parenthesis.
Servo Mode â¢ Set the test mode, press the VOL â key and use the â/+ key to set the servo mode. â¢ When the servo mode is set, use the +/â key and the = key on the set to move the optical pick-up to the outer circumference and to the inner circumference respectively. â¢ When entering another mode, refer to the configuration of test mode. 1. Structure of Servo Mode
Servo mode 000
p key â/ + key
Offset adjustment 010
â/ + key
011 to 014
Short : Test mode Open : Normal mode
*1 â/ + key
Releasing the Test Mode A test mode releasing method varies depending on the test mode setting method. 1. When test mode was entered with key input, turn off the power. 2. When test mode was entered by shorting the test point, turn off the power and open the solder bridge of TAP805 (TEST MODE) on the MAIN board. Operation of Setting on Test Mode When the test mode is set, the LCD displays the following :
Laser power adjustment 020
â/ + key
021 to 024 *1 â/ + key
(See page 7.)
100 V1. 000
LCD on remote commander
ROM version display
â¢ The cycle - the above ROM version display n All lit n All off - is repeated. â¢ When the PLAYMODE key is pressed and hold down, the display at that time is held so that display can be checked.
*1 Repeatedly press â/ + key to change the mode. (Refer to the following list for a description of each mode.)
VOL +/â keys
Complete owner's manual in digital format. The manual will be available for download as PDF file aft…