There are currently no product reviews.
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
You can fully trust on this one!
All the schematics are very crear an in one piece per page
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
SECTION 4 TEST MODE
Outline â¢ In this set, overall adjustment mode is made available by entering test mode to perform automatic adjustment of CD and MO. In the overall adjustment mode, the disc is determined whether it is CD or MO and adjustments are performed in sequence. If a fault is found, the location of the fault is displayed. Also, in servo mode, each adjustment can be automatically made. â¢ Operation in the test mode is performed with the Remote Commander. A key having no particular description in the text, indicates a Remote Commander key. Setting the Test Mode To enter the test mode, two methods are available : 1. Entering method with key input. Turn on the HOLD switch on the set. While holding down the p key on the set, press the following remote commander keys in the following order : +n+n=n=n+n=n+n =nPnP 2. Entering method by shorting the test point Solder bridge the test point TAP801 (TEST) on the main board (connect IC801 pin #â¢ to GND), and turn on the POWER.
[MAIN BOARD] (Conductor side)
Configuration of Test Mode The test mode has the configuration given below.
VOL + key p key Overall adjustment mode (Auto?) p key p key VOL â key p key Adjustment â key mode (Manu ?) Servo mode 000 +, â keys Audio mode 100 +, â keys Power mode 300 Displays of the LCD on the remote commander are shown in parentheses. â key
Servo Mode â¢ Set the test mode, press the VOLUME â key and use the â key to set the servo mode. â¢ When the servo mode is set, use the + key and the = key to move the optical pick-up to the outer circumference and to the inner circumference respectively. â¢ When entering another mode, refer to the configuration of test mode. 1. Structure of Servo Mode
Servo mode 000 p key â key
Display when test mode
Offset adjustment 010
Test mode Short : Test mode Open : Normal mode
011 to 013 *1 â key
Releasing the Test Mode 1. When test mode was entered with key input, turn off the POWER. 2. When test mode was entered by shorting the test point, turn off the POWER and open the solder bridge of TAP801 (TEST MODE) on the main board. Operation of Setting on Test Mode
Laser power adjustment 020
+, â keys
021 to 024 *1 â key
When the test mode is set, the LCD displays the following :
2 (See page 8.)
ROM version display LCD on remote commander
â¢ The cycle - the above ROM version display n All lit n All off - is repeated. (The ROM version is constantly displayed.) â¢ When the PLAY MODE key is pressed and hold down, the display at that time is held so that display can be checked.
*1 Repeatedly press â key to change the mode. (Refer to the following list for a description of each mode.)
+, â keys
Complete owner's manual in digital format. The manual will be available for download as PDF file aft…