There are currently no product reviews.
El producto satisface las necesidades del servicio t
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
ItΒ΄s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
SECTION 4 ELECTRICAL ADJUSTMENTS
TEST MODE This set have the test mode function. In the test mode, FM Auto Scan/Stop Level and MW Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure. <Set the Test Mode> 1. Set the âpower selectâ switch (S700) is âA (ON) â position. 2. Turn ON the regulated power supply. (All LEDs on the set lights up, and the clock is displayed.)
Note: Press the [OFF] button, if the clock is not displayed.
Procedure: 1. Set to the test mode. 2. Push the [SOURCE] button and set to FM. Display
3. 4. 5. 6.
Push the preset  button. Push the preset  button. Press the preset  button for more than two seconds. Then the display indicates all lights, the test mode is set.
3. Adjust with the volume RV2 on TU1 so that the âFMâ indication turns to âFM0â indication on the display window. But, in case of already indicated âFM0â, turn the RV2 so that put out light â0â indication and adjustment. Display
<Release the Test mode> 1. Push the [OFF] button. 2. Return the âpower selectâ switch (S700) to initially set position.
See the adjustment location from on page 16 for the adjustment.
Adjustment Location: See page 16. FM Stereo Separation Adjustment Setting: [SOURCE] button: FM
FM RF signal generator antenna jack (J1) 0.01 ÂµF set 4â¦ + â level meter
MD section adjustments are done automatically in this set.
0 dB=1 ÂµV
Cautions during repair When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.
Carrier frequency Output level Mode Modulation
Note: Adjust the tuner section in the sequence shown below. 1. FM Auto Scan/Stop Level Adjustment. 2. FM Stereo Separation Adjustment. 3. MW Auto Scan/stop Level Adjustment. 4. RDS S-Meter Adjustment.
: 98.0 MHz : 70 dB (3.2 mV) speaker out terminal : stereo : main: 1 kHz, 33.75 kHz deviation (45%) sub: 1 kHz, 33.75 kHz deviation (45%) 19 kHz pilot: 7.5 kHz deviation (10%)
FM Stereo signal generator output channel L-CH R-CH L-CH L-CH R-CH R-CH A B Adjust RV4 on TU1 for minimum reading. C D L-CH Adjust RV4 on TU1 for minimum reading. Level meter connection Level meter reading (dB)
FM Auto Scan/Stop Level Adjustment Setting: [SOURCE] button: FM
FM RF signal generator
antenna jack (J1)
Carrier frequency Output level Mode Modulation : 98.0 MHz : 22 dB (12.6 ÂµV) : mono : 1 kHz, 22.5 kHz deviation (30%)
L-CH Stereo separation: A-B R-CH Stereo separation: C-D The separations of both channels should be equal. Specification: Separation more than 30 dB Adjustment Location: See page 16.
â 14 â