|
|
|
Who's Online
There currently are 5899 guests and
2 members online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
;
Nothing wrong with the manual or the delivery - came to me the same day I ordered it. But afterwards I realized that I ordered the wrong manual. Probably better with the Quick start - version. So maybe it would be better if we could see a list with inhold for each manual before ordering?
5-5. TEMPERATURE COMPENSATION OFFSET ADJUTMENT
Save the temperature data at that time in the non-volatile memory as 25 �C reference data. Note : 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 �C to 28 �C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature of 22 �C to 28 �C. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature. Adjusting Method : 1. Rotate the AMS knob and display �TEMP ADJUST�. 2. Press the YES button and select the �TEMP ADJUST� mode. 3. �TEMP = � and the current temperature data will be displayed. 4. To save the data, press the YES button. When not saving the data, press the NO button. 5. When the YES button is pressed, �TEMP = SAVE� will be displayed and turned back to �TEMP ADJUST� display then. When the NO button is pressed, �TEMP ADJUST� will be displayed immediatelly. Specified Value : The �TEMP = � should be within �E0 - EF�, �F0 - FF�, �00 0F�, �10 - 1F� and �20 - 2F�.
5-6. LASER PPOWER ADJUSTMENT
Connection :
Laser power meter
Optical pick-up objective lens Digital volt meter
BD board CN110 pin 5 (I+3V) CN110 pin 4 (IOP)
Adjusting Method : 1. Set the laser power meter on the objective lens of the optical pick-up. (When it cannot be set properly, press the 0 button or ) button to move the optical pick-up.) Connect the digital volt meter to CN110 pin 5 (I+3V) and CN110 pin 4 (IOP). 2. Rotate the AMS knob and display �LDPWR ADJUST�. (Laser power : For adjustment) 3. Press the YES button once and display �LD 0.9 mW $ �. 4. Rotate the AMS knob so that the reading of the laser power meter becomes 0.86 to 0.92 mW. Press the YES button after setting the range knob of the laser power meter, and save the adjustment results. (�LD SAVE $ � will be displayed for a moment.) 5. Then �LD 7.0 mW $ � will be displayed. 6. Rotate the AMS knob so that the reading of the laser power meter becomes 6.9 to 7.1 mW, press the YES button and save it. Note : Do not perform the emission with 7.0 mW more than 15 seconds continuously. 7. Then, rotate the AMS knob and display �LDPWR CHECK�. 8. Press the YES button once and display �LD 0.9 mW $ �. Check that the reading of the laser power meter become 0.85 to 0.91 mW. 9. Press the YES button once more and display �LD 7.0 mW $ �. Check that the reading the laser power meter and digital volt meter satisfy the specified value. Specified Value : Laser power meter reading : 7.0 ± 0.1 mW Digital voltmeter reading : Optical pick-up displayed value ± 10% (Optical pick-up label)
KMS
27X40 B0825
Iop = 82.5 mA in this case Iop (mA) = Digital voltmeter reading (mV)/1 (�)
10. Press the NO button and display �LDPWR CHECK� and stop the laser emission. (The NO button is effective at all times to stop the laser emission.)
N
260A
� 32 �
 $4.99 MDSS38 SONY
Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|
