|
|
|
Who's Online
There currently are 5925 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thanks you very much for this "hard to find" service manual.
Will help a lot in repairing this tuner.
;
I have this hi-fi system for a long time and I need to repair some things. Founding this manual will be very helpfull :)
 ;
It is pretty good. The schematics were covered all components, the manual also provide the parts list . It's useful for the trouble shooting.
;
Very fast service, best quality of the service manual and the schematics
;
This service manual of the old video cassette recorder VT-LC50EM is very good readable even the tiniest numbers (i.e. IC-pins). The circuits are very clear. Many details of the schematic are very good described but in GERMAN language. Many schematic details - but complete at all. Common background information of several details are enclosed and physical knowledge of the TFT liquid crystal display for example. The manual lacks PCB drawings. If you understand german I would recommend this manual for you.
SECTION 3 SET-UP ADJUSTMENTS
� � �
When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments. Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply. Unless there are specific instructions to the contrary, set the controls and switches to the following settings : Contrast .................................. normal
Carry out the adjustments in the following order : 3-1. Beam Landing and Geometry. 3-2. Convergence. 3-3. Focus. 3-4. White Balance. Note : Test equipment required. 1. Color bar/pattern generator. 2. Degausser. 3. Oscilloscope. 4. Digital multimeter.
Brightness .................................. normal
3-1. Beam Landing
Preparation : 1. 2. In order to reduce the influence of geomagnetism on the set�s picture tube, face it in an easterly or westerly direction. Switch on the TV set�s power and degauss with a degausser. (2) Landing and Geometry Note : Before carrying out the following adjustments adjust the magnets as indicated on page 22 [See Fig.3-4]. 1. Input a crosshatch signal from the signal generator. 2. Rough-adjust the focus and horizontal convergence. 3. Switch from the crosshatch pattern to an all-red pattern. 4. Move the deflection yoke backwards and adjust with the purity magnet so that the red is at the centre and it aligns symmetrically [See Fig.3-5]. 5. Move the deflection yoke forward to the point where the entire screen just becomes red [Mark its position]. 6. Move the deflection yoke further forward until the screen just changes colour at the edges. [Mark its position]. 7. Position the deflection yoke between the two marks indicated above. 8. Input a crosshatch pattern from the pattern generator and rotate the deflection yoke so that the horizontal lines are parallel with the top and bottom of the screen. 9. When the position of the deflection yoke has been determined, fasten it with its fixing screw. 10. Once dy rotation and swing left and right for h linearity is ok on cross hatch pattern, insert dy wedges. [See Fig.3-6]. 11. Switch the pattern generator to green then blue and confirm the purity. 12. If the beam does not land correctly in all the corners of the screen, use disk magnets to correct it. [Confirm the corner landing forgreen and blue]. 13. Re-check geometry for landing magnet effect. Adjust using deflection menu. [TT Mode].
(1) Adjustment of Correction Magnet for Y-Splitting Axis. 1. 2. 3. 4. 5. 6. Input a crosshatch signal from the pattern generator. Set the Picture control to minimum and confirm that the Brightness control is set to normal. Position the neck assembly as indicated in Fig.3-3. Loosen the deflection yoke fixing screw. Move the deflection yoke as far forward as is possible. Adjust the upper and lower pin symmetrically by opening or closing the Y-splitting axis correction magnets located on the neck assembly. [See Fig 3-2] Return the deflection yoke to its original position and re-tighten its fixing screw.
7.
Fig.3-1 Y-splitting axis correction magnet
Fig.3-3
Neck assy
G2 G1
Fig.3-2
+
Align the edge of the neck assy on the edge of the G3 grid closest to the G2 grid.
G3
Caution : High voltages are present on the Deflection yoke terminals - take care when handling the Deflection yoke whilst carrying out adjustments.
- 21 -
|
|
|
> |
|
