|
|
|
Who's Online
There currently are 5855 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Impeccable, document très complet. Perfect, i get all i need. All schematic are correct. Thanks
;
The manual is of better quality compared to other. I found it less expensive and therefore it it is the best buy cost vs quality.
 ;
I bought the service-manual of the sony ICB-1020(an old transmitter-receiver) at "www.Owners-Manual.com", I found the service-manual for a fairly cheap price(in comparison with other sellers). I filled in some questions, payed the order with Ideal, and within 24 hours I had my service manual. I was very happy:In no time I had my service-manual and everything, but literally everything was noted down in the manual; the electronic scheme, the parts list, etcetera.
A very practical, reference-document.
;
This comprehesive service maual was greatly appreciated, as was the digital download.
;
Good en helpfull black and white scanned Srfvice manual of the Philps D8444. Quick service and delivery
ICF-CD863/CD863L
Adjustment Location:
� MAIN BOARD (Component Side) �
AUTO BRIGHTNESS ADJUSTMENT Connecting:
digital voltmeter LCD board TP (DIMMER) TP (GND) 100 k � + �
CD SECTION
CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias.
FOCUS BIAS CHECK
1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the u (CD) button. 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (�) in the center of the waveform can be clearly distinguished. � RF signal reference waveform (eye pattern)
VOLT/DIV: 0.2 V (with the 10: 1 probe in use.) TIME/DIV: 500 ns
CT4 LW VCO Voltage Adjustment (CD863L) L4 AM (MW) VCO Voltage Adjustment RV1 FM Stereo Adjustment L1 FM RF CT2 Tracking Adjustment
}
T1 AM IF Adjustment
1. Set to power off state. 2. Connect a digital voltmeter to TP (DIMMER) and TP (GND) on the LCD board and confirm that the voltage is 0 V. 3. Turn on the power. 4. Connect the digital voltmeter to TP (DIMMER) and TP (GND) on the LCD board and adjust RV401 so that the voltage becomes 1.5 ± 0.05 V. 5. Turn off the power. 6. Applied sufficient light to IC403 (brightness sensor) on the DIMMER board and confirm that the voltage is 3.3 ± 0.3 V. 7. Short the BP404. Adjustment Location: � LCD BOARD (Component Side) �
0.8 ± 0.2 Vp-p
L3-1 AM (MW) Tracking CT2 Adjustment
}
L3-2 LW Tracking Adjustment CT3 (CD863L)
}
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.
Adjustment Location:
� MAIN BOARD (Conductor Side) �
TP (FM IN)
RV401 Auto Brightness Adjustment
� CD BOARD (Conductor Side) �
TP (GND) TP (VT) TP (FM ST)
IC701
� LCD BOARD (Conductor Side) �
TP (GND)
TP (RADIO B+)
TP (GND)
TP (RF)
1 4 CN303
TP (DIMMER)
� DIMMER BOARD (Conductor Side) �
IC403
13
13
|
|
|
> |
|
