Shopping cart is empty
 
English Polski Spanish 
Search For a Manual
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Who's Online
There currently are 388 guests online.
Categories
Information
Featured Product
Home >> SONY >> HCDV818 Service Manual
 
 0 item(s) in your cart 

SONY HCDV818
Service Manual


Tweet about this product and get $1.00 of store credit for instant use!
  • Contains Circuit Diagrams
  • Download
  • PDF Format
  • Complete manual
  • Language: English
Price: $4.99

Description of SONY HCDV818 Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagrams, printed circuit boards, repair tips, wiring diagrams, block diagrams and parts list. Service Manual ( sometimes called Repair Manual ) is used mainly by technicians.

If You just want to know how to use Your tv, video, mp3 player etc. You should look for Owner's Manual. After placing order we'll send You download instructions on Your email address.

The manual is available in languages: English

Not yet ready
You must purchase it first

Customer Reviews
There are currently no product reviews.
Other Reviews
 SC-3330 SANSUI Service Manual by Marc LO BONO;
Acurate informations inside the SM and I could repair my old Sansui SC-3330 without any problems. Thanks.
 7045 NAD Service Manual by Marc LO BONO;
I used it to repair a NAD 7030, but unfortunately, the 7045 is different ! But documentation was useful.
 STR-4800 SONY Service Manual by Marc LO BONO;
Content A4 and A3 format pages. Exactly what I needed to restore my old receiver.
 STR-5800 SONY Service Manual by Marc LO BONO;
Content A4 and A3 format pages. Exactly what I needed to restore my old receiver.
 DCX 6000K SANYO Service Manual by Marc LO BONO;
Thanks you very much for this "hard to find" service manual. Will help a lot in repairing this receiver.

Text excerpt from page 19 (click to view)
CD SECTION
NOTE :

Note : A clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform.
RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns

1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. S Curve Check
oscilloscope BD board TP (FE) TP (VC) + –

level : 1.3 +0.25 Vp-p
–0.20

E-F Balance (Traverse) Check (Without remote comander)
oscilloscope BD board TP (TE) TP (VC) + –

Procedure : 1. Connect oscilloscope to test point TP (FE) on BD board. 2. Connect between test point TP (FEI) and TP (VC) by lead wire. 3. Turned Power switch on. 4. Put disc (YEDS-18) in and turned Power switch on again and actuate the focus search. (actuate the focus search when disc table is moving in and out.) 5. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3±1 Vp-p.
S-curve waveform
symmetry

Procedure : 1. Short-circuit SL502 of the video board to GND. 2. Connect oscilloscpe to test point TP (TE) on BD board. 3. Turned Power switch on. Press FUNCTION button to select CD. 4. Set a disc (YEDS-18) and play. 5. Press the PLAY MODE button. (The sledding servo is turned OFF.) 6. Check the level B of the oscilliscope’s waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than ± 7%
Traverse waveform

A Within 3 ± 1 Vp-p B B Center of the waveform

6. After check, remove the lead wire connected in step 2. Note : • Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. • Take sweep time as long as possible and light up the brightness to obtain best waveform. RF Level Check
oscilloscope BD board TP (RF) TP (VC) + –

0V

A (DC voltage)

level : 500 mV ± 100 mVp-p

7. Press the PLAY MODE button. (The tracking servo and sledding servo are turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 6.
Traverse waveform

0V

C (DC voltage)

Procedure : 1. Connect oscilloscope to test point TP (RF) on BD board. 2. Turned Power switch on. 3. Put disc (YEDS-18) in to play the number five track. 4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.

Sled servo OFF

Sled servo ON

– 19 –

You might also want to buy

$4.99

SX-K700 TECHNICS
Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file aft…

$4.99

CJ-V51 PIONEER
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…

$4.99

SX-PR602 TECHNICS
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…

$4.99

AG7330 PANASONIC
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…

$4.99

HC-P4752W SAMSUNG
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…

$4.99

SX-KN2000 TECHNICS
Service Manual

Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…

$4.99

AG-7500 PANASONIC
Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file aft…

$4.99

VSX-95 PIONEER
Owner's Manual

Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
>
Parse Time: 0.135 - Number of Queries: 132 - Query Time: 0.028