|
Who's Online
There currently are 6034 guests and 1 member online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This service manual helped me to repair my PIONEER. Iam very satisfied, that I found it here.
Even the price of manual was not so high that person would not be able to spend a few money.
But that is very worth spent money. Thanks
;
Excellent quality service manual. Quick processing, fair prices. Love to do business again. Thank you!!!
;
Excellent service manual, the only known point of note is the alignment of improvability scanned pages within the pdf page. The resolution is good.
;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
3-11. HEAD CLEANING WHEN HEAD CLOGGING OCCURS
Clean the video head as follows when the head gets dirty. . Procedure to use the cleaning cassette 1. Insert the cleaning cassette DVM12CL in the DSR-85/ 85P and press the [PLAY] key immediately (within 1 second). Make sure that the [EJECT] key flashes, the [PLAY] key lights and the display appears. Note : . Use only the DVM12CL cleaning cassette tape. If another cleaning cassette tape is used, abnormal abrasion or breakage of the video head could occur. . Press the [PLAY] key immediately after inserting the cleaning cassette tape. 2. The cleaning cassette tape is automatically ejected after running for 10 seconds. Note : Do not rewind the cleaning cassette tape to use it again. 3. Make sure that the head is no longer dirty. If the video head is still dirty after step 2 above, clean the video head as follows. . Procedure to use the cleaning cloth 1. Soak the cleaning cloth with cleaning liquid and bring it into contact lightly with the video head. 2. Turn the upper drum slowly by hand in the rotating direction of the head (counterclockwise when viewed from the top) to clean the video head. Note : . Never move the cleaning cloth in the vertical direction against the video head because it may break the head. . Turn the power switch off when cleaning the video head.
3-12. OPERATING THE VTR WITHOUT A CASSETTE TAPE
When adjusting the mechanical block, the VTR is sometimes operated without a cassette tape. This section describes how to do this. 1. Remove the cassette compartment from the DSR-85/ 85P or remove the connector of the cassette compartment. 2. Turn on switches S501-3 and 4 of the SY-220 board, then turn on the main power. Note : If switch S501-3 of the SY-220 board is not on, an error will occur. The operating method of each mode is as follows. . THREADING After the reel motor and the upper drum rotate, the threading ring rotates to enter the threading mode. The tension arm and the threading ring move to the specified position, then the threading is completed. This condition in which the threading is completed is referred to as the STOP status. . PLAY Press the [PLAY] key. The pinch roller is pressed against the capstan shaft to enter the PLAY status. When the [PLAY] key is pressed during threading, the pinch roller is pressed against the capstan shaft to enter the PLAY status after the threading has completed. . FF Press the [F|FWD] key. . The pinch roller is pressed against the capstan shaft to set the FWD.SEARCH to five-times speed. . REW Press the [REW] key. The pinch roller is pressed against the capstan shaft to set REV.SEARCH to five-times speed.
DSR-85/85P
3-37
|
|
|
> |
|