There are currently no product reviews.
Wanting to repair a neighbours tape recorder I needed the necessary information, it makes it easier. Although the service manual is described as "Language : English" To my dismay I found that it is entirely written in German, a language I do not understand. At least I now have the schematics which will help of sorts. I may not use this service again due to the laguage difficulty after all when it states English you do not expect it to be entirely in another language.
GOOD SERVICE MANUAL.I ALWAYS BUY THERE IF I FIND WHAT I AM LOKING
Good quality (clearly readable) manual, I'm glad I could find it here, at a bargain price!
Speedy transaction with a quick download. Awesome hassle-free service.
very poolite and healpful secure transaction thanks allot
SECTION 5 MECHANICAL ADJUSTMENTS
Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode FWD FWD back tension REV REV back tension FF/REW Torque meter CQ-102C Meter reading 3.04 â 6.96 N â¢ m (31 to 71 g â¢ cm) (0.43 â 0.98 oz â¢ inch) 0.20 â 0.58 N â¢ m (2 to 6 g â¢ cm) (0.02 â 0.08 oz â¢ inch) 3.04 â 6.96 N â¢ m (31 to 71 g â¢ cm) (0.43 â 0.98 oz â¢ inch) 0.20 â 0.58 N â¢ m (2 to 6 g â¢ cm) (0.02 â 0.08 oz â¢ inch) 6.97 â 14.02 N â¢ m (71 to 143 g â¢ cm) (0.98 â 1.99 oz â¢ inch) 0.98 N â¢ m or more (100 g or more) (3.53 oz or more) 0.98 N â¢ m or more (100 g or more) (3.53 oz or more)
HCD-CL1/CL3 SECTION 6 ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB=0.775V
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjusted. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and R-CH. 7. Switches and controls should be set as follows unless otherwise specified.
Tape P-4-A100 WS-48B Signal 10 kHz, â10 dB 3 kHz, 0 dB Used for Azimuth Adjustment Tape Speed Adjustment
Record/Playback Head Azimuth Adjustment Procedure: 1. Mode : Playback
test tape P-4-A100 (10kHz, â10dB) main board CN301 Pin 1 (L-ch) Pin 3 (R-ch) set
FWD tension REV tension
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak.
within 1 dB within 1dB
R-CH peak screw position
Complete owner's manual in digital format. The manual will be available for download as PDF file aft…