|
|
|
Who's Online
There currently are 5959 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High-quality scanning. Detailed description. Recommend for all technician. A+++
;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
;
Great product. Recieved it fast...exactly as advertised.
SECTION 1 SERVICING NOTES
1-1. WRITING FOCUS/TRACKING AUTO GAIN DATA
In general for the CD players that use a digital servo IC, the focus/ tracking gain is automatically adjusted each time a disc is changed. In this set, the gain in test disc (YEDS-18) has been written to a nonvolatile memory (IC803: X24C01S) on the Display Board, and therefore the gain is not readjusted even if a disc is changed. Accordingly, always write auto gain data when replacing the Servo Board, IC803 on Display Board, or optical pick-up. 1)Connect CN805 1 pin (IN/OUT SW) and 6 pin (GND) on Display Board. Under this condition, the set will operate even when the disc lid is open (or Key Board is not connected). 2)Connect TP (ADJ: CN105 3 pin) on Servo Board to GND, and TP (VC: CN108 2 Pin) to TP3 (TEI: IC105 @¶ pin) with lead wires respectively. 3)Connect an oscilloscope to TP (TE: CN108 1 pin).
Oscilloscope SERVO board TP (TE) TP (VC)
+ �
1-2. AF MODE
With the TP (AFJ: CN105 2 Pin) connected to the GND on Servo Board, turn on the POWER switch, and the AF mode is activated and the following checking can be made. 1-2-1. FL tube check All tubes turn on, then if · button is pressed, the display will be as shown below. (Segment ON 1)
(Segment ON 1)
IF P button is pressed, the display will be as shown below. (Segment ON 2)
2 6 12 16 18 8 14 20 4 10
(Segment ON 2)
4)Insert the test disc (YEDS-18), turn on POWER switch, and play fifth music with · (PLAY) and AMS Keys on the Remocon. 5)Adjust RV101 so that the waveform on oscilloscope is verticolly symmetric with respect to the A [Vdc], and also its level is 1.3 ± 0.6 Vp-p.
B 0Vdc A
If STOP p is pressed, all tubes turn on again.
symmetric level: 1.3 ± 0.6 Vp-p
At this time, A/B � 100 = ± 22 (%) or less 6)The auto gain data are written when a lead wire between TP (ADJ: CN105 3 pin) and GND is removed. Note: If the POWER switch was turned on without connecting TP (ADJ) to the GND, auto gain data are not written to the memory even if a disc is inserted, but the previous data saved in the memory are used as focus/tracking data.
�3�
|
|
|
> |
|
