There are currently no product reviews.
It is perfect, exactly what we needed. It's like the paper version but less clutter.
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
Immediate response with excellent service - highly reccommended
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
6-2. ELECTRICAL ADJUSTMENT
Note: 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10Mâ¦ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. S-Curve Check
oscilloscope BD board TP (FE1) TP (VC)
Note: A clear RF signal waveform means that the shape âââ can be clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200mV TIME/DIV : 500ns level : 1.2
Adjustment Location: BD board E-F Balance Check
oscilloscope BD board TP (TE) TP (VC)
Procedure : 1. Chuck the disc (YEDS-18) beforehand, and disconnect the power cord from the outlet. 2. Connect oscilloscope to test point TP (FE1) on BD board. 3. Connect test point TP1 (ADJ) on MAIN board to ground with lead wire. 4. The ADJ mode is set when the power cord is inserted into the outlet and power is supplied. 5. The fifth track is played automatically. 6. Press the CHECK button. 7. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3Â±1 Vp-p.
Procedure : 1. Chuck the disc (YEDS-18) beforehand, and disconnect the power cord from the outlet. 2. Connect oscilloscpe to test point TP (TE) on BD board. 3. Connect test point TP1 (ADJ) on MAIN board to ground with lead wire. 4. The ADJ mode is set when the power cord is inserted into the outlet and power is supplied. 5. The fifth track is played automatically. 6. Press the GROUP 3 button. (The tracking servo and the sledding servo are turned OFF.) 7. Check the level B of the oscilliscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than Â± 22%
A Within 3 Â± 1 Vp-p B
Center of the waveform B
8. Pressing the 1/u button stops the output of the waveform (s curve). 9. After check, remove the lead wire connected in step 3. Note : â¢ Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. â¢ Take sweep time as long as possible and light up the brightness to obtain best waveform. Adjustment Location: BD board
A (DC voltage)
level : 1.3 Â± 0.6 mVp-p
8. Press the GROUP 8 button. (The tracking servo and sledding servo are turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 7.
RF Level Check
oscilloscope BD board TP (RF) TP (VC)
C (DC voltage)
Procedure : 1. Connect oscilloscope to test point TP (RF) on BD board. 2. Turn Power switch on. 3. Put disc (YEDS-18) in to play the number five track. 4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
Tracking servo Sledding servo OFF
Tracking servo Sledding servo ON
9. Disconnect the lead wire of TP1 (ADJ) connected in step 2. Adjustment Location: MAIN board
â 17 â