There are currently no product reviews.
This manual is complete and of high quality. I am very pleased with the purchase.
Another excellent buy! A fully readable PDF archive. Good prints!!
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
very good manual, with detail and clarity in esquematic diagrams and waveforms .
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) â¢ b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) â¢ Through hole is omitted. â¢ Circled numbers refer to waveforms. â¢ There are few cases that the part printed on diagram isnât mounted in this model. â¢ Chip parts. Transistor
C 654 456 4 5 1 2 3
CD-209 (CCD IMAGER) PRINTED WIRING BOARD â Ref. No. CD-209 Board; 10,000 Series â CD-209 BOARD
C1401 C1405 C1406 C1407 C1408 C1409 C1410 C1411 C1412 A-2 A-1 A-1 B-2 B-2 B-1 B-1 B-2 B-1
(Measuring conditions voltage and waveform)
â¢ Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 Mâ¦ input impedance is used.). â¢ Voltage values change depending upon input impedance of VOM used.) 1. Connection
CN1401 A-3 IC1401 A-3 IC1402 B-2
L1401 L1402 R1401 R1405 R1406 R1407 R1408 R1409
A-2 B-1 A-1 A-1 B-2 B-2 B-2 B-1
(For schematic diagrams) â¢ All capacitors are in ÂµF unless otherwise noted. pF : ÂµÂµF. 50V or less are not indicated except for electrolytics and tantalums. â¢ Chip resistors are 1/10W unless otherwise noted. kâ¦=1000â¦, Mâ¦=1000kâ¦. â¢ Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. â¢ Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520
Front of the lens
Kinds of capacitor Temperature characteristics External dimensions (mm)
â¢ Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. â¢ Parts with 5 differ according to the model/destination. Refer to the mount table for each function. â¢ All variable and adjustable resistors have characteristic curve B, unless otherwise noted. â¢ Signal name â¢ â¢ â¢ â¢ â¢ â¢ â¢ XEDIT â EDIT PB/XREC â PB/REC 2 : non flammable resistor 1 : fusible resistor C : panel designation A : B+ Line B : Bâ Line J : IN/OUT direction of (+,â) B LINE. C : adjustment for repair.
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Green Yellow White Cyan
AB A=B BA Fig. a (Video output terminal output waveform)
Red White Magenta Blue Red Blue
Electron beam scanned frame
CRT picture frame
For printed wiring boards â¢ This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.
â¢ Circled numbers refer to waveforms. Note : The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
There are few cases that the part printed on this diagram isnât mounted in this model.
Fig.b (Picture on monitor TV)
When indicating parts by reference number, pleas include the board name.
VF-129 (B/W EVF) CD-209 (CCD IMAGER) VL-23 (VIDEO LIGHT)
VF-129 (B/W EVF) CD-209 (CCD IMAGER)
1 IC1401 1,2
2 IC1401 3,4
3 IC1401 7
4 IC1401 !â¢
5 IC1401 !Â£,!Â¢
6 IC1402 6
DD-117 (DC/DC CONVERTER) MA-351 DD-117 (DC/DC CONVERTER) MA-351 STEREO MIC AMP, LASER LINK PJ-92 (AV IN/OUT) SE-83 (STEADY SHOT)
6.8Vp-p H H 1.1Vp-p 14.187 MHz
3.3Vp-p 14.187 MHz
3.7Vp-p H 1.2Vp-p
STEREO MIC AMP, LASER LINK PJ-92 SE-83 (AV IN/OUT) (STEADY SHOT)