|
Who's Online
There currently are 5929 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
2-4. Analog Video Gain Adjustment
2-4. Analog Video Gain Adjustment
Measurement Equipment Waveform /vector monitor Procedures 1. Supply 75 % color bars signal of the 4:2:2 component 525/60 serial digital video format to the SDI IN connector. 2. Set S2(A-4) to NTSC. 3. Set S3(A-7) to D1. 4. Check the waveform of the ANALOG MONITOR OUT and adjust 1RV101(D-4) to satisfy the specification.
8. Set S2(A-4) to PAL. 9. Check the waveform of the ANALOG MONITOR OUT to satisfy the specification.
A
Spec. : A = 1.00 ±0.01 Vp-p
10. Check to see that each luminescent point is placed inside the "4" frame on the vectorscope.
V cy g R Mg
A
YL yl
b U B
G
Cy r
mg
Spec. : A = 140.0 ±1.4 IRE (1.00 ±0.01 Vp-p )
5. Check to see that each luminescent point is placed inside the "4" frame on the vectorscope.
R�Y I R Mg Q
11. Check to see that the image on the video monitor screen is under normal conditions. 12. Supply 75 % color bars signal of the NTSC composite serial digital video format to the SDI IN connector. 13. Set S2 to NTSC. 14. Set S3 to D2. 15. Check the waveform as step 4 and adjust 1RV7(F-7) to satisfy the specification. 16. Check to see that each luminescent point is placed inside the "4" frame on the vectorscope as step 5.
YL B�Y B
�Q
G
Cy �I
17. Supply 75 % color bars signal of the PAL composite serial digital video format to the SDI IN connector. 18. Set S2 to PAL. 19. Check the waveform as step 9 and adjust 1RV8(G-7) to satisfy the specification. 20. Check to see that each luminescent point is placed inside the "4" frame on the vectorscope as step 10.
6. Check to see that the image on the video monitor screen is under normal conditions. 7. Supply 75 % color bars signal of the 4:2:2 component 625/50 serial digital video format to the SDI IN connector.
BKPF-113
2-5(E)
|
|
|
> |
|